New | AP1055F Mobil-Trac Paver

The AP1055F is a high-production rubber track paver that excels on airports runways, interstates, highways, and other large jobsites. It's high travel speed, flotation, and traction deliver superb mobility.

Tractor Operating Weight37553 lb
Tractor Shipping Weight36804 lb
Operating Weight w/SE60 V45090.0 lb
Operating Weight w/SE60 V XW46580.0 lb
Operating Weight w/SE60 VT XW48320.0 lb
Operating Specifications
Standard Paving Range3.0-6.0 m (9' 10" - 19' 6")
Maximum Paving Width - SE60 V Screed25 ft
Maximum Paving Width - SE60 V XW, VT XW Screeds33 ft
Maximum Paving Speed with Tamper Bar Screed82.0 ft/min
Maximum Paving Speed with Vibratory Screed210.0 ft/min
Maximum Travel Speed9 mph
Inside Turning Radius1.5 ft
Hopper Capacity - Standard Entry267.0 ft3
Hopper Capacity - Low Entry Hopper286 ft3
Maximum Throughput Capacity1766 Tons per Hour
Operating Width - Standard Entry Hopper132 in
Operating Width - Low Entry Hopper142 in
Operating Height with Canopy157 in
Operating Height without Canopy146 in
Operating Length with SE60 V Screed22.5 ft
Operating Length with SE60 V XW, VT XW Screeds23.1 ft
Transport Length with SE60 V Screed20 ft
Transport Length with SE60 XW-Series22.7 ft
Transport Width with Screed End Gates10.66 ft
Transport Width with End Gates Folded9.83 ft
Transport Height - Canopy Retracted10.5 ft
Transport Height - without Canopy10.45 ft
Truck Entry Height with Standard Entry Hopper22.5 in
Truck Entry Height with Low Entry Hopper20.5 in
Gross Power225.0 hp
Engine ModelCat C7.1 with ACERT
Service Refill Capacities
Fuel Tank Capacity92.0 gal
DEF Tank5 gal

Efficient power management and advanced Eco-mode optimize fuel efficiency and lower sound levels.

Cat C7.1 Engine

The C7.1 engine provides 168 kW (225 hp) and meets U.S. EPA Tier 4 Final and EU Stage IV emmision standards.


Eco-mode utilizes an engine speed of 1650 rpm and reduces fuel burn by up to 5% over Cat E-series pavers while also lowering sound levels even more.

Automatic Engine Speed Control

When automatic engine speed control is activated, the engine speed is reduced to an idle speed of 1000 rpm when the propel lever is moved to neutral or to 1300 rpm when screed heat is active.

Advanced Eco-mode

Eco-mode and automatic engine speed control when activated together modify the engine rpm based on load factors. When activated the engine will operate at 1650 rpm when paving. If the upper power threshold is exceeded, the engine speed will increase to 2200 rpm and remain there until the demand drops below the threshold and remains there for 30 seconds, ensuring reliable performance.

Exclusive 70 kW integrated generator delivers fast heating screed plates, quiet or quick heating options, and simple monitoring. The system is designed to save time and fuel while providing reliability for the life of the paver. Advanced diagnostics keep the screed heating, even in the event of a sensor failure.

Quiet Heating

Quiet heat mode operates at an engine speed of 1300 rpm and provides screed plate heating in under 15 minutes.

Quick Heating

Quick heating mode provides a heat-up time in under 35 minutes when equipped with the 10 m (33 ft) wide-width paving package.

Temperature Ranges

Three preset heating options provide a wide range of temperatures for various mix designs; Low is 110 degrees C or 230 degrees F, medium is 130 degrees C or 266 degrees F, high is 160 degrees C or 320 degrees F.

The dual operator stations provide complete control and good visibility to truck drivers from either side of the operating platform. Station transfer occurs with the simple press of a button and all the settings automatically transfer making the transition from side to side very easy.

Better Visibility, Exceptional Comfort

The dual independent operating stations can extend beyond the frame for good all-around visibility. The low profile, front-mounted cooling system improves forward viewing and the redesigned auger assembly optimizes visibility to material height in front of the screed. The heated seat option, multiple seat adjustments, and tilting consoles conform to the operator to provide day-long comfort. The top-mounted cooling system directs fumes, hot air, and fan noise away from the crew for a cooler and quieter working environment.

Fumes Management

The exclusive ventilation system draws fumes from the conveyor tunnel as well as the auger chamber and redirects them away from the operator for a more comfortable working environment.

The water resistant displays provide excellent reliability and meet IP67 common water submergence ratings. The switches have been tested to one million cycles without failure. If a failure does occur, grouped coomponents are serviceable and it's not necessary to replace the entire console.

Single Touch Operation

Single touch features for the auto-fill feeder system, feeder system activation, and hopper control, allow operators to concentrate on truck exchanges and other duties for improved efficiency.

Simple Technology

Technology helps operators perform. Intuitive symbols and large graphics simplify operation, while the interactive LCD display with touchscreen access to generator activation, screed temperature control, and mix height adjustment, increase efficiency.

High production features include large throughput capacity and over-sized feeder components that enable the system to run slower, limiting wear while also reducing fuel consumption.

Auto-Fill Feeder System

The auto fill feeder system simplifies starts by alternating the conveyors and augers until the mix height reaches the sensor set point, eliminating manual activation and constant monitoring.

Single Touch Feeder System

The two augers and two conveyors can be activated automatically with a single button, simplifying setup. Each auger and each conveyor can still be operated independently when needed.

One Touch Hopper Control

The hopper wings and hydraulic apron can be folded with a single touch and release. The system can be tailored to activate left or right wings, or the front hydraulic apron independently or together.

Cleanout and Warm-Up Mode

This feature activates the augers, conveyors, and tamper-bar (if equipped) at a reduced speed, allowing the application of release agents to prevent material build-up.

Mix Height Adjustment

Mix height adjustment in front of the screed can be modified from the tractor LCD display for increased versatility when needed.

Hydraulic Mainframe Extensions

The optional 457 mm (18") hydraulic mainframe extensions attach to the auger assembly and provide smooth material flow out to the extenders. They retract with the screed extensions when reducing paving widths.

Multiple Feed Sensor Options

The feeder system can be tailored to automatically operate with 0, 2, or 4 feeder sensors. When paving with 0 sensors due to a failure, simply set the feeder system to automatic and adjust the mix height setting, no need to cycle the manual switch as previous models required.

Easier Service

Hardware-free bed plates simplifies replacement and bottom side mounting hardware for the chain gaurds eliminates bolt wear and material build-up for easier replacement.

Maintenance-free and unmatched traction in both smooth or tread-bar style belts, the Mobil-Trac undercarriage provides excellent flotation, smooth travel, and high speed capability for better mobility around the job site.


The Mobil-Trac undercarriage minimizes tow-point movement. The front and rear bogie sets crawl over obstacles and help maintain ground contact. The smooth belt option performs well on soft base materials and fresh mats. The tread-bar design excels on loose paving/transport conditions.


Self-tensioning accumulators, center guide blocks, and rugged internal belt cables ensure durability. The components are rubber coated in order to shed asphalt and prevent accumulation.

The SE60-Series screeds provide new heating technology, increased durability, easy adjustment, and better efficiency. The XW-Series screeds offer a maximum paving width out to 10 m (33 ft) and are available with tamper bars and vibration or vibration only.

Screed Heat Technology

Exclusive zone monitoring allows heating to continue in the event of a temperature sensor failure. The system also monitors heating elements for failure conditions, eliminating unnecessary replacement.

Easy Adjustment

Feeder system ratio adjustment capability from the screed provides versatility. Standard hydraulic adjustment for extender height, slope, and crown, allows for on-the-go adjustment at standard and maximum paving widths.

Two-Speed Proportional Extender Control

Exclusive two-speed proportional extender control offers slower speed for precise control around obstacles and quick reaction when extending paving widths.

Simple Replacement

The heating elements slide out for easy replacement, no need to remove the screed plates. Machined screed frames simplify plate replacement and leveling.

Tamper Bar Screed Option

Tamper bar equipped screeds increase density as it tucks material under the screed plates. Three stroke settings of 2, 4, and 7 mm provide versatility and has a variable tamper speed of 0 to 1800 rpm.

Wide-Width Paving Packages

Exclusive power controls simplify adjustment across the entire 10 m (33 ft 4 in) paving width for better mat texture and quality. An innovative hooking system utilizes extender slope to attach wide-width paving packages, eliminating the need for other lifting devices.

Cat Grade Control is a factory-integrated guidance system that helps remove irregularities from the surface and control mat thickness for increased production, lower operating costs, and higher profitability.

Easy Operation

F-Series pavers allow Cat Grade Control to be operated from any of the two tractor or two screed consoles. Split screen mode can be setup to monitor each side of the screed allowing single person operation.

Precise Control

More accurate control maximizes mix utilization and saves money. True averaging with sonic sensors that utilize 5 transducers, 2 readings are discarded and 3 averaged. A 10-point Auto-Calibration eliminates over/under adjustment from a single calibration point. Cross-coupling, slope and elevation are maintained with height adjustments. The true 9 m (30 ft) sonic averaging beam modifies tow point movement by 1/3 of total grade deviation.

Highly Reliable

Water-resistant displays, factory installed components, and consistent routing deliver performance. Sealed components withstand heat, moisture, and vibration, while the built-in temperature sensors provide better reliability than bail-type sensors.











Machine Comparison

Other Models in this Category

Select Product Category

Why Cat is Better. Machine Comparison

80 percent of our heavy equipment fleet is Caterpillar. We are extremely satisfied with Hawthorne Cat’s service and staff. Hawthorne Cat is the obvious choice for our equipment needs - now and in the future.”
Sam Wathen
SC Valley Engineering, Inc

San Diego
Ross Farmer
Sales Manager
858.674.7048 office
760.815.4094 mobile

Bobby Whitworth
General Manager
808.676.0353 office
808.864.5147 mobile