New | ATC Service Entrance Rated MCCB & Power Breaker Based ATS

Cat® Service Entrance Rated (SER) automatic transfer switches (ATS) are designed to provide standby power emergency power to entire installation loads to protect against utility power interruption; yet allow the ATS to be as close as possible to the point of service entrance. By safely and in code compliance, integrating the necessary overcurrent protection and service disconnecting means into the automatic transfer switch, a single installation can be made at the service entrance. This design eliminates the need for a separate upstream fault protection and respective interconnections, which in turn reduces installation space, time, and cost. Breaker-based Service Entrance Rated transfer switches are available from 30A to 5000A.

• Specifications
• Benefits & Features
• Equipment
• Photos
• Downloads

Technical Summary
Rating Range	30-5000A
Transfer Type	Open / Closed / Delayed
Switch Type	Molded Case and Power Breaker
Ratings
MCCB	30-1000A 2, 3, or 4 Pole
Fixed Mount Power Breaker	200-3200A 2, 3, 4-Pole
Drawout Power Breaker	200-5000A 2, 3, or 4-Pole
System Voltage Application	120-600 Vac 50/60 Hz
Withstand	(Power Breaker) Up to 100 kAIC at 600V 3 cycles
Applicable Testing	UL 1008 listed up to 3200A 4000A, and 5000A UL 891 listed

Product Features

• atc-100 On Residential & Light Commercial Mccb Based, Atc-300+ Or Atc-800 On Mccb & Power Breaker Ats Products
• ul 1008 Service Entrance Listed (up To 3200a)
• service Disconnect (both Off) Capability
• integral Over Current Protection
• lockout When In Disconnected Position (only)
• service Entrance Labeled
• integrated Design
• disconnecting Neutral Assembly
• ground Fault Protection Capability (all Ratings)
  (required By Code On Rating 480v, And 1000a Or Higher)
• keyed Service Entrance Switch
• draw-Out Type Breakers (available On Power Breaker Ratings)
• ul 891 For 4000-5000a
• loads Protected Against Extended Power Loss
• quick Restoration Of The Circuit After A Trip (versus A Fused Circuit That Requires Fuse Availability)
• trip On A Fault Prohibits Transfer To The Emergency Source
• fused Circuit Allows Switch Testing By Simulating An Actual Power Failure
• lockable Disconnect Position Permits Safe Downstream Maintenance

Standard Equipment

Controls and Wiring All controls relays and industrial grade relays are totally encapsulated to minimize exposure to dust and dirt. Lugs are 90º rated and all control wire is #16 AWG, type XLPE with a 125º temperature rating.

Enclosure Durable powder-coated steel NEMA 1, 3R or 12 enclosures with three door hinges to ensure proper support of the door and door mounted devices. The hinges have removable hinge pins to facilitate door removal for easy wall mounting or service and are supplied with pad-lockable latches.

Optional Equipment

Available Options 4-position test switch Remote communications Surge suppression Selectable automatic or non-automatic operation Seismic Zone 4 Qualified (BOCA, CBC, IBC, UBC and OSHPD) Communications for the ATC-300+ controller via RS-232 or Modbus through an integrated RS-485 port Field selectable, multi ratio, control voltage transformer 50/60 Hz Load sequencing contacts Multi-meter options available Open, closed or delayed transition Space heaters Integral overcurrent protection

Optional Delayed Transition includes: Pre-transfer signal with 1 N.O. and 1 N.C. contacts Time delay neutral

listofrelationships

Download ATC Service Entrance Rated MCCB & Power Breaker Based ATS Spec Sheet

Download Cat Gensets Rating Guide

Other Models in this Category

• ATC Contactor Based Bypass Isolation Automatic Transfer Switch - 18505945
• ATC Contactor-Based Automatic Transfer Switch - 18505862
• ATC Molded Case Circuit Breaker & Molded Case Switch Automatic Transfer Switch - 18506281
• ATC Power Breaker & Case Switch Automatic Transfer Switch - 18506045
• ATC Power Breaker Bypass Isolation Open/Closed Transition ATS - 18503093
• ATC-100 CONTROLLER - 18502972
• ATC-300+ CONTROLLER - 18502989
• ATC-800 CONTROLLER - 18503033

Select Integrated System Type

• Switchgear and Paralleling Controls
• ATS MX Contactor