627
627 Wheel Tractor-Scraper
DESCRIPTION
Quick loading, high travel speeds and the ability to load and dump on the run yield fast cycle times, allowing Cat Wheel Tractor-Scrapers to consistently deliver high productivity at the lowest cost per ton.The principal choice for moving material on an earthmoving site is the Cat®627 Wheel Tractor-Scraper. Twin-powered for high rolling resistance and steep grades, this machine is engineered to work effectively in a wide range of conditions and materialtypes. Whether traveling through sand, clay, or shot rock, it’s specifically designed to fit an earthmover’s needs for today‘s and
tomorrow’s work.
Wheel Tractor-Scraper K Series
Wheel Tractor-Scraper K Series Operator Testimonial
BE MORE PRODUCTIVE
- The Advanced Productivity Electronic Control System (APECS) allows the engine and transmission to communicate on a high level. This communication allows the machine to better utilize the power and torque the engine is producing. The net result is moving more material.
- Use Ground Speed Control to set the desired top speed and the machine will find the gear that works best for the engine and the transmission, providing a lower fuel burn.
- The Machine Speed Limit feature replaces Top Gear Selection.
- Auto-Stall assists in quickly bringing the transmission to an operating temperature at start-up when the machine is working in a cold climate region.
- Enhance productivity through the usage of Cat Payload with
Sequence Assist. - Cat Payload for scrapers is an earthmoving solution for optimal payload and job site efficiency. Cat Payload achieves on-the-go weighing by using bowl lift cylinder pressure during the loaded haul segment. Cat Payload is optimized to be used with Sequence Assist, which provides increased productivity with less operator effort.
WORK IN COMFORT
- Reduce up to 14 individual operator commands per cycle with
Sequence Assist. - Steer with less effort with the newly designed high-pressure steering
system. - Enjoy interior improvements and a more ergonomic work environment
with a 21% larger cab than the G Series cab. - Intuitive, ergonomic controls keep operators focused on their work.
- Maintain desired cab temperature with automatic temperature control
.
DESIGNED FOR SAFETY
- Enhance an operator’s awareness of site surroundings with the Work
Area Vision System (WAVS). - The seatbelt indicator provides visual and audible alerts when the seatbelt is not in use.
- The Advanced Cushion Hitch enables the cushion hitch to prevent endstroke by predicting endstroke events and controlling the rate of damping, resulting in reduced hitch maintenance and an improved operator ride in rough conditions.
EASY TO OPERATE
- The spacious cab features easy, intuitive controls and excellent
visibility. The cab provides a comfortable working environment for
all-day operation. - Cat Advanced Ride Management (ARM) seat suspension reduces
endstroke movement of the load cylinder for a smoother ride. - Engine overspeed protection will automatically engage with no
operator input when the machine is in eighth gear. The machine
will assist in slowing the machine’s speed by canceling the throttle
command and engaging the engine compression brake.
INTEGRATED CAT TECHNOLOGIES
- Monitor, manage, and enhance job site operations.
- Hit target grade faster and more accurately with Cat Grade technologies. Finish jobs in fewer passes and with less operator effort, saving you time and helping to increase profit.
- Product Link™ collects machine data that can be viewed online
through web and mobile applications (optional attachment). - Access information anytime, anywhere with VisionLink® – use it to make informed decisions that boost productivity, lower costs, simplify maintenance, and improve safety and security on your
jobsite. - Shorten the learning curve for inexperienced operators with
Sequence Assist and Load Assist (included with Cat Grade attachment).
EXECUTE EFFICIENCY
- The tractor's hydraulic on-demand fan helps reduce fuel consumption.
- The Cat C13 tractor engine and C9.3 scraper engine meet U.S. EPA
Tier 4 Final and EU Stage V emission standards, or U.S. EPA Tier 2/
equivalent to U.S. EPA Tier 3 and EU Stage IIIA emission standards,
contributing to lower fuel consumption. - Using draft-arm overflow guards diverts material away from the bowl, preventing material from getting caught between the draft arms and the bowl sides.
- Cat Grade (optional attachment) intelligently ensures the machine
does not cut below grade in a cut area or overfill in the fill area.
- Standard Equipment
- Optional Equipment
- Specs
- Docs
Standard Equipment
- NOTE
- Standard and optional equipment may vary. Consult your Cat dealer for details.
- POWER TRAIN – TRACTOR
- Cat® C13
- Cat engine brake
- Electric start, 24 Volt
- Air cleaner, dry type with precleaner
- Fan, hydraulic
- Ground level engine shutdown
- Radiator, aluminum unit core, 9 fins per inch
- Guard, crankcase
- Muffler (only for less or non-regulated regions engine arrangement only)
- Starting aid, ether
- Braking system:
– Primary and secondary, wet disc, hydraulic
– Parking, hydraulic-released, spring-applied
– Throttle lock - Transmission:
– 8-speed planetary power shift
– ECPC control
– APECS software
– Programmable top gear selection
– Transmission hold
– Differential lock
– Guard, power train
– Standard tire spin reduction
– Ground speed control
– Machine speed limit
– Differential lock protection
- POWER TRAIN – SCRAPER
- Cat® C9.3 engine with high pressure:
– Common rail fuel
– Cat engine brake
– Electric start, 24 volt
– Fan, driveline
– Ground engine shutdown
– Muffler (only for less or non-regulated regions engine arrangement only)
– Starting aid, ether - Braking system:
– Primary and secondary, wet disc, hydraulic
– 4 speed (torque converter drive)
– Transmission planetary powershift
- Cat® C9.3 engine with high pressure:
- ELECTRICAL – TRACTOR
- Alternator, 150 Amp
- Batteries (4), 12V, 1,000 CCA, maintenance free, high output
- Electrical system, 24V
- Lighting system:
– Headlights, 3×3 halogen
– Turn signals with hazard function, LED floodlights, (2) 3×3 cutting edge (1) 3×3 bowl, halogen side vision (2) 3×3 halogen - Starting/charging receptacle
- ELECTRICAL – SCRAPER
- Alarm, backup
- Alternator, 65 Amp
- Batteries (4), 12V, 1,000 CCA, maintenance free, high output
- Lighting system:
– Brake lights, LED
– Turn signals with hazard function, LED - Starting/charging receptacle
- OPERATOR ENVIRONMENT – TRACTOR
- HVAC system, heat, AC, defrost
- Thermostat control of HVAC system
- Coat hook
- Lunchbox platform with holding strap
- Diagnostic connection (2)
- 12V power ports (2)
- Differential lock (1)
- Dome courtesy light
- Horn, electric
- T-Handle implement control
- Mirror, rearview
- Radio ready
- ROPS/FOPS cab, pressurized
- Keypad switches:
– Rear engine start
– Throttle lock
– Wipers/washers
– Hazard lights
– Retarding level select
– Work lights on, off
– Information mode on Messenger Display - Safety tab rocker switches:
– Regeneration control
– Parking brake - Seat belt, static two-piece
- Seat, Cat Advanced Ride Management (ARM), Cat Comfort Series 3, rotates 30 degrees
- Steering wheel, tilt, telescoping, padded
- Windows, right side emergency egress
- Windows, sliding
- Windows, laminated, zipped in
- Windshield wipers, front and rear windows, includes washers
- Door lock
- Messenger Display
- Gauges, warnings include:
– Coolant temperature
– Engine oil temperature
– Hydraulic oil temperature
– Fuel level
– Park brake
– Implement lockout
– Brake system
– Regeneration required
– Throttle lock
– System voltage
– Secondary steering
– Bail down
– Differential lock
– Apron float
– Transmission hold
– Cushion hitch
– High beam lights
– Action lamp
– Engine speed, rpm
– Gear selection
- FLUIDS
- Extended Life Coolant to –37° C (–34° F)
- OTHER STANDARD EQUIPMENT – TRACTOR
- Advanced cushion hitch
- Accumulators (cushion hitch) with Canadian Registration Number (CRN)
- Fast oil change
- Fenders, non-metallic
- Heater, engine coolant 120V
- Rims (2)
- Tow pin, front
- Vandalism locks
- Heater, engine coolant 120V
- OTHER STANDARD EQUIPMENT – SCRAPER
- Bowl
– 18.4 m³ (24 yd³), heaped
– 14.1 m³ (18.4 yd³), struck
– Fast oil change
– Vandalism locks
– Guard, overflow
– Heater, engine coolant 120V - Hydraulic position sensing cylinders (bowl lift and apron)
- Bowl
- SPECIAL ARRANGEMENTS
- Tractor/Scraper Arrangements
– Push Pull Arrangement - Fueling Arrangements
– Fast Fill Group
- Tractor/Scraper Arrangements
Optional Equipment
- NOTE
- Standard and optional equipment may vary. Consult your Cat dealer for details.
- STEERING ARRANGEMENTS
- Secondary Steering Arrangement
- INTEGRATED TECHNOLOGIES
- Sequence Assist Arrangement
- Load Assist
- Cat Grade Control with Load Assist
- Product Link™ Installation
- WORK LIGHT ATTACHMENTS
- HID work lights
- AMBIENT CAPABILITY ARRANGEMENTS
- Cooling, high ambient HRC
- Cooling, low ambient HRC
- Cooling, high ambient LRC
- Cooling, low ambient LRC
- CLEANER
- Cab precleaner
- OTHER ATTACHMENTS
- Camera arrangement – WAVS
- Steering lock – external
- Cab beacon
- Air horn
- Air horn and beacon
- Wiring group
- Year of manufacture plate
- SERVICE INSTRUCTIONS
- Film arrangement – U.S. (ANSI)
- Film arrangement – International (ISO)
Specs
Overview
Long Name:
627 Wheel Tractor-Scraper
Name:
627
Brand:
Caterpillar
Status:
Current
Tractor Engine
Flywheel Power - Tractor/Scraper
304 kW (407 hp)/216 kW (290 hp)
Scraper Bowl
Scraper Capacity - Heaped
24 yd³ / 18.4 m³
Transmission
Top Speed - Loaded
33.5 mile/h / 53.9 km/h
Engine
Engine Model - Tractor
Cat® C13
Engine Model - Scraper
Cat® C9.3
Note (1)
Cat® C13 engine emits equivalent to U.S. EPA Tier 2/EU Stage II or U.S. EPA Tier 3/EU Stage III.
Note (2)
Cat® C9.3 engine emits equivalent to U.S. EPA Tier 2/EU Stage II or U.S. EPA Tier 3/EU Stage III.
Rated Engine RPM - Tractor
2000 r/min / 2000 r/min
Flywheel Power - Tractor
407 hp / 304 kW
Rated Engine RPM - Scraper
2150 r/min / 2150 r/min
Flywheel Power - Scraper
290 hp / 216 kW
General
Scraper Capacity - Struck
17.1 yd³ / 13 m³
Scraper Capacity - Heaped
24 yd³ / 18.4 m³
Width - Cut
10.3 ft / 3.14 m
Maximum Depth of Cut
12.4 in / 315 mm
Maximum Depth of Spread
21.3 in / 540 mm
Top Speed - Loaded
33.5 mile/h / 53.9 km/h
Rated Load
26 127 kg (57,610 lb); 26.19 tonnes (28.81 tons)
Overall Width
11.71 ft / 3.57 m
Overall Shipping Height
13.22 ft / 4.03 m
Tires - Tractor Drive
33.25R29**E3
Tires - Scraper
33.25R29**E3
180° Curb-to-Curb Turning Width
38.71 ft / 11.8 m
Travel Speeds - Runout
Transmission Gear - First
3.1 mile/h / 5 km/h
Transmission Gear - Second
5.5 mile/h / 8.9 km/h
Transmission Gear - Third
7.5 mile/h / 12.1 km/h
Transmission Gear - Fourth
10.1 mile/h / 16.3 km/h
Transmission Gear - Fifth
13.6 mile/h / 21.9 km/h
Transmission Gear - Sixth
18.4 mile/h / 29.6 km/h
Transmission Gear - Seventh
24.8 mile/h / 39.9 km/h
Transmission Gear - Eighth
33.5 mile/h / 53.9 km/h
Transmission Gear - Reverse
5.7 mile/h / 9.2 km/h
Service Refill Capacities
Crankcase - Tractor
8.08 gal (US) / 30.58 l
Transmission System - Tractor
24.76 gal (US) / 93 l
Cooling System - Tractor
11.89 gal (US) / 45 l
Diesel Exhaust Fluid - Tractor
8.1 gal (US) / 30.5 l
Fuel Tank
336.03 gal (US) / 1272 l
Hydraulic System
21.926 gal (US) / 83 l
Crankcase - Scraper
7.397 gal (US) / 28 l
Transmission System - Scraper
12.944 gal (US) / 49 l
Cooling System - Scraper
16.114 gal (US) / 61 l
Brake Cooling (Scraper)
8.7 gal (US) / 33 l
Diesel Exhaust Fluid - Scraper
5.8 gal (US) / 22 l
Note
*When equipped
Dimensions
Width - Overall Machine
141.1 in / 3585 mm
Width - Tractor
133.1 in / 3381 mm
Width - Inside of Bowl
120 in / 3048 mm
Width - Outside Rear Tires
128.9 in / 3275 mm
Height - Overall Shipping
158.6 in / 4029 mm
Height - Top of Cab
142.6 in / 3621 mm
Ground Clearance - Tractor
21.9 in / 557 mm
Front of Tractor to Front Axle
122.8 in / 3119 mm
Axle to Vertical Hitch Pin
21.3 in / 540 mm
Height - Scraper Blade Maximum
20.5 in / 520 mm
Wheel Base
314.9 in / 7998 mm
Rear Axle - Rear of Machine
114.1 in / 2898 mm
Width - Overall Machine - Ladder Down
149.2 in / 3790 mm
Width - Rear Tire Centers
90.2 in / 2290 mm
Length - Overall Machine - Standard
551.8 in / 14015 mm
Length - Maximum (Push-Pull)
613.2 in / 15576 mm
Service Refill Capacities - Tractor
Differential
41.7 gal (US) / 158 l
Final Drive - Each
5 gal (US) / 19 l
Service Refill Capacities - Scraper
Differential
8.98 gal (US) / 34 l
Final Drive - Each
5 gal (US) / 19 l
Non Push-Pull
Overall Length
45.9 ft / 14.02 m
Operating Weight - Empty
90213 lb / 40913 kg
Push-Pull
Overall Length - With Bail Down
51.1 ft / 15.58 m
Operating Weight - Empty
92980 lb / 42168 kg
Cab
Exterior Sound Level
The exterior sound power level for the standard machine (ISO 6393) is 119 dB(A).
ROPS/FOPS
Meets ISO standards
Safety Criteria Compliance Standards
Rollover Protection Structure (ROPS)
ISO 3471:2008 for up to 17 084 kg (37,664 lb)
Falling Object Protective Structure (FOPS)
ISO 3449:2005 Level II
Brakes
ISO 3450:2011
Steering System
ISO 5010:2007
Seat Belt
SAE J386:JUN1985
Reverse Alarm
ISO 9533:2010
Notes
*If equipped with optional secondary steering
Implement Cycle Times
Bowl Raise
3 s / 3 s
Apron Raise
2.95 s / 2.95 s
Ejector Extend
5.2 s / 5.2 s
Bail Raise
1.8 s / 1.8 s
Ejector Retract
6.7 s / 6.7 s
Bail Lower
3.2 s / 3.2 s
Apron Lower
3.8 s / 3.8 s
Bowl Lower
3.5 s / 3.5 s
General
Fuel Tank Refill Capacity - Scraper
336 gal (US) / 1272 l
SEE HOW 627 COMPARES AGAINST FREQUENTLY COMPARED PRODUCTS.
Open Bowl Scrapers
627
- Brand
- Caterpillar
- Status
- Current
- Flywheel Power - Tractor/Scraper
- 304 kW (407 hp)/216 kW (290 hp)
- Scraper Capacity - Heaped
- 24 yd³ / 18.4 m³
- Top Speed - Loaded
- 33.5 mile/h / 53.9 km/h
- Engine Model - Tractor
- Cat® C13
- Rated Engine RPM - Tractor
- 2000 r/min / 2000 r/min
- Flywheel Power - Tractor
- 407 hp / 304 kW
- Scraper Capacity - Struck
- 17.1 yd³ / 13 m³
- Width - Cut
- 10.3 ft / 3.14 m
- Maximum Depth of Cut
- 12.4 in / 315 mm
- Maximum Depth of Spread
- 21.3 in / 540 mm
- Rated Load
- 26 127 kg (57,610 lb); 26.19 tonnes (28.81 tons)
- Overall Width
- 11.71 ft / 3.57 m
- Overall Shipping Height
- 13.22 ft / 4.03 m
- Tires - Scraper
- 33.25R29**E3
- 180° Curb-to-Curb Turning Width
- 38.71 ft / 11.8 m
- Transmission Gear - First
- 3.1 mile/h / 5 km/h
- Transmission Gear - Second
- 5.5 mile/h / 8.9 km/h
- Transmission Gear - Third
- 7.5 mile/h / 12.1 km/h
- Transmission Gear - Fourth
- 10.1 mile/h / 16.3 km/h
- Transmission Gear - Fifth
- 13.6 mile/h / 21.9 km/h
- Transmission Gear - Sixth
- 18.4 mile/h / 29.6 km/h
- Transmission Gear - Seventh
- 24.8 mile/h / 39.9 km/h
- Transmission Gear - Eighth
- 33.5 mile/h / 53.9 km/h
- Transmission Gear - Reverse
- 5.7 mile/h / 9.2 km/h
- Fuel Tank
- 336.03 gal (US) / 1272 l
- Hydraulic System
- 21.926 gal (US) / 83 l
- Width - Overall Machine
- 141.1 in / 3585 mm
- Width - Tractor
- 133.1 in / 3381 mm
- Width - Inside of Bowl
- 120 in / 3048 mm
- Width - Outside Rear Tires
- 128.9 in / 3275 mm
- Height - Overall Shipping
- 158.6 in / 4029 mm
- Height - Top of Cab
- 142.6 in / 3621 mm
- Ground Clearance - Tractor
- 21.9 in / 557 mm
- Front of Tractor to Front Axle
- 122.8 in / 3119 mm
- Axle to Vertical Hitch Pin
- 21.3 in / 540 mm
- Height - Scraper Blade Maximum
- 20.5 in / 520 mm
- Wheel Base
- 314.9 in / 7998 mm
- Rear Axle - Rear of Machine
- 114.1 in / 2898 mm
- Width - Overall Machine - Ladder Down
- 149.2 in / 3790 mm
- Width - Rear Tire Centers
- 90.2 in / 2290 mm
- Length - Overall Machine - Standard
- 551.8 in / 14015 mm
- Length - Maximum (Push-Pull)
- 613.2 in / 15576 mm
- Overall Length
- 45.9 ft / 14.02 m
- Operating Weight - Empty
- 92980 lb / 42168 kg
- Overall Length - With Bail Down
- 51.1 ft / 15.58 m
- Exterior Sound Level
- The exterior sound power level for the standard machine (ISO 6393) is 119 dB(A).
- ROPS/FOPS
- Meets ISO standards
- Rollover Protection Structure (ROPS)
- ISO 3471:2008 for up to 17 084 kg (37,664 lb)
- Falling Object Protective Structure (FOPS)
- ISO 3449:2005 Level II
- Brakes
- ISO 3450:2011
- Steering System
- ISO 5010:2007
- Seat Belt
- SAE J386:JUN1985
- Reverse Alarm
- ISO 9533:2010
- Bowl Raise
- 3 s / 3 s
- Apron Raise
- 2.95 s / 2.95 s
- Ejector Extend
- 5.2 s / 5.2 s
- Bail Raise
- 1.8 s / 1.8 s
- Ejector Retract
- 6.7 s / 6.7 s
- Bail Lower
- 3.2 s / 3.2 s
- Apron Lower
- 3.8 s / 3.8 s
- Bowl Lower
- 3.5 s / 3.5 s
- Fuel Tank Refill Capacity - Scraper
- 336 gal (US) / 1272 l
Selected Model
Open Bowl Scrapers
621
- Brand
- Caterpillar
- Status
- Current
- Flywheel Power - Tractor/Scraper
- 304 kW (407 hp)
- Scraper Capacity - Heaped
- 24 yd³ / 18.4 m³
- Top Speed - Loaded
- 33.5 mile/h / 53.9 km/h
- Engine Model - Tractor
- Cat® C13
- Rated Engine RPM - Tractor
- 2000 r/min / 2000 r/min
- Flywheel Power - Tractor
- 407 hp / 304 kW
- Scraper Capacity - Struck
- 17.1 yd³ / 13 m³
- Width - Cut
- 10.3 ft / 3.14 m
- Maximum Depth of Cut
- 12.4 in / 315 mm
- Maximum Depth of Spread
- 21.3 in / 540 mm
- Rated Load
- 26 127 kg (57,610 lb); 26.19 tonnes (28.81 tons)
- Overall Width
- 11.75 ft / 3.58 m
- Overall Shipping Height
- 13.22 ft / 4.03 m
- Tires - Scraper
- 33.25R29**E3
- 180° Curb-to-Curb Turning Width
- 38.71 ft / 11.8 m
- Transmission Gear - First
- 3.1 mile/h / 5 km/h
- Transmission Gear - Second
- 5.5 mile/h / 8.9 km/h
- Transmission Gear - Third
- 7.5 mile/h / 12.1 km/h
- Transmission Gear - Fourth
- 10.1 mile/h / 16.3 km/h
- Transmission Gear - Fifth
- 13.6 mile/h / 21.9 km/h
- Transmission Gear - Sixth
- 18.4 mile/h / 29.6 km/h
- Transmission Gear - Seventh
- 24.8 mile/h / 39.9 km/h
- Transmission Gear - Eighth
- 33.5 mile/h / 53.9 km/h
- Transmission Gear - Reverse
- 5.7 mile/h / 9.2 km/h
- Fuel Tank
- 216.09 gal (US) / 818 l
- Hydraulic System
- 21.926 gal (US) / 83 l
- Width - Overall Machine
- 141.1 in / 3585 mm
- Width - Tractor
- 133.1 in / 3381 mm
- Width - Inside of Bowl
- 120 in / 3048 mm
- Width - Outside Rear Tires
- 128.9 in / 3275 mm
- Height - Overall Shipping
- 158.6 in / 4029 mm
- Height - Top of Cab
- 142.2 in / 3612 mm
- Ground Clearance - Tractor
- 21.9 in / 557 mm
- Front of Tractor to Front Axle
- 122.8 in / 3119 mm
- Axle to Vertical Hitch Pin
- 21.3 in / 540 mm
- Height - Scraper Blade Maximum
- 20.5 in / 520 mm
- Wheel Base
- 314.9 in / 7998 mm
- Rear Axle - Rear of Machine
- 114.1 in / 2898 mm
- Width - Overall Machine - Ladder Down
- 149.2 in / 3790 mm
- Width - Rear Tire Centers
- 90.2 in / 2290 mm
- Length - Overall Machine - Standard
- 551.8 in / 14015 mm
- Length - Maximum (Push-Pull)
- 613.2 in / 15576 mm
- Overall Length
- 45.9 ft / 14.02 m
- Operating Weight - Empty
- 80630 lb / 36567 kg
- Overall Length - With Bail Down
- 51.1 ft / 15.58 m
- Exterior Sound Level
- The exterior sound power level for the standard machine (ISO 6393:2008) is 118 dB(A).
- ROPS/FOPS
- Meets SAE and ISO standards
- Rollover Protection Structure (ROPS)
- ISO 3471:2008 for up to 17 084 kg (37,664 lb)
- Falling Object Protective Structure (FOPS)
- ISO 3449:2005 Level II
- Brakes
- ISO 3450:1996
- Steering System
- ISO 5010:2007
- Seat Belt
- SAE J386:JUN1985
- Reverse Alarm
- ISO 9533:2010
- Bowl Raise
- 3 s / 3 s
- Apron Raise
- 2.95 s / 2.95 s
- Ejector Extend
- 5.2 s / 5.2 s
- Bail Raise
- 1.8 s / 1.8 s
- Ejector Retract
- 6.7 s / 6.7 s
- Bail Lower
- 3.2 s / 3.2 s
- Apron Lower
- 3.8 s / 3.8 s
- Bowl Lower
- 3.5 s / 3.5 s
- Fuel Tank Refill Capacity - Scraper
- 216.1 gal (US) / 818 l
Open Bowl Scrapers
631
- Brand
- Caterpillar
- Status
- Current
- Flywheel Power - Tractor/Scraper
- 570 hp / 425 kW
- Scraper Capacity - Heaped
- 34 yd³ / 26 m³
- Top Speed - Loaded
- 34.7 mile/h / 55.8 km/h
- Engine Model - Tractor
- Cat® C18
- Rated Engine RPM - Tractor
- 1900 r/min / 1900 r/min
- Flywheel Power - Tractor
- 570 hp / 425 kW
- Scraper Capacity - Struck
- 24 yd³ / 18.3 m³
- Width - Cut
- 17.7 ft / 3.51 m
- Maximum Depth of Cut
- 12.4 in / 450 mm
- Maximum Depth of Spread
- 21.1 in / 535 mm
- Rated Load
- 37 200 kg (82,200 lb); 37.2 tonnes (41.1 tons)
- Overall Width
- 12.11 ft / 3.94 m
- Overall Shipping Height
- 12.9 ft / 3.89 m
- Tires - Scraper
- 37.25R35**E3
- 180° Curb-to-Curb Turning Width
- 40.12 ft / 12.23 m
- Transmission Gear - First
- 3.4 mile/h / 5.5 km/h
- Transmission Gear - Second
- 6.2 mile/h / 10 km/h
- Transmission Gear - Third
- 7.7 mile/h / 12.4 km/h
- Transmission Gear - Fourth
- 10.5 mile/h / 16.9 km/h
- Transmission Gear - Fifth
- 14.1 mile/h / 22.7 km/h
- Transmission Gear - Sixth
- 19 mile/h / 30.6 km/h
- Transmission Gear - Seventh
- 25.7 mile/h / 41.4 km/h
- Transmission Gear - Eighth
- 34.7 mile/h / 55.8 km/h
- Transmission Gear - Reverse
- 6.2 mile/h / 9.9 km/h
- Fuel Tank
- 231 gal (US) / 874 l
- Hydraulic System
- 37.5 gal (US) / 142 l
- Width - Overall Machine
- 155 in / 3937 mm
- Width - Tractor
- 144.2 in / 3662 mm
- Width - Inside of Bowl
- 134 in / 3404 mm
- Width - Outside Rear Tires
- 143.2 in / 3636 mm
- Height - Overall Shipping
- 153.2 in / 3892 mm
- Height - Top of Cab
- 149.8 in / 3805 mm
- Ground Clearance - Tractor
- 26.1 in / 664 mm
- Front of Tractor to Front Axle
- 142 in / 3608 mm
- Axle to Vertical Hitch Pin
- 20 in / 509 mm
- Height - Scraper Blade Maximum
- 20 in / 510 mm
- Wheel Base
- 346.8 in / 8808 mm
- Rear Axle - Rear of Machine
- 108 in / 2744 mm
- Width - Overall Machine - Ladder Down
- 159.3 in / 4045 mm
- Width - Rear Tire Centers
- 96.9 in / 2462 mm
- Length - Overall Machine - Standard
- 596.8 in / 15160 mm
- Length - Maximum (Push-Pull)
- 655.2 in / 16643 mm
- Overall Length
- 49.34 ft / 15.04 m
- Operating Weight - Empty
- 106430 lb / 48275 kg
- Overall Length - With Bail Down
- 54.59 ft / 16.64 m
- Exterior Sound Level
- The exterior sound power level for the standard machine (ISO 6393) is 116 dB(A).
- ROPS/FOPS
- ROPS/FOPS meet “ISO Standards.”
- Rollover Protection Structure (ROPS)
- ISO 3471:2008 for up to 21 282 kg (46,919 lb)
- Falling Object Protective Structure (FOPS)
- ISO 3449:2005 Level II
- Brakes
- ISO 3450:2011
- Steering System
- ISO 5010:2007
- Seat Belt
- SAE J386:FEB2006
- Reverse Alarm
- ISO 9533:2010
- Bowl Raise
- 3.5 s / 3.5 s
- Apron Raise
- 4 s / 4 s
- Ejector Extend
- 8.5 s / 8.5 s
- Bail Raise
- 1.5 s / 1.5 s
- Ejector Retract
- 8.5 s / 8.5 s
- Bail Lower
- 2.1 s / 2.1 s
- Apron Lower
- 3.8 s / 3.8 s
- Bowl Lower
- 3.5 s / 3.5 s
- Fuel Tank Refill Capacity - Scraper
- 231 gal (US) / 874 l
