C7 ACERT™ (Water-Cooled Manifold)
C7 ACERT™ Water-Cooled Manifold Engine
DESCRIPTION
Cat C7 ACERT engines are the ideal solution for your demanding operations in the oilfield. Decades of field operation and intense research and development allow Cat C7 ACERT engines to deliver excellent performance with low operating costs and emissions. Applications powered by C7 ACERT engines include pump skids, acidizing units, cementing units, coil tubing units, and hydraulic power units. Cat engines are backed by the worldwide network of Cat dealers ready to support your operation with technical support, service, parts, and warranty. C7 ACERT engines, with ratings: 153 - 224 bkW (205 - 300 bhp) @ 2200 rpm meet IMO Tier II, U.S. EPA Marine Tier 3, EPA Non-road Tier 3 equivalent and EU Stage IIIA equivalent emission standards. They are available using U.S. EPA and EU Flexibility, and for other regulated and non-regulated areas.Technology
- Electrical harness containing point-to-point wiring without splices in any power/signal wires - Electrical harnesses and connectors are overmolded and are routed through urethane tube for protection against impact and vertical flame propagation. - To meet safety requirements, connectors require the use of a special tool to be disconnected and bear the “do not disconnect while energized” warning. - Optional ATEX and NEC certified 25-foot customer harness - ECU is certified as part of the engine to restricted breathing per EN 60079-15. ECU is protected with a stainless steel guard. - Fuel injector connections at valve cover bases are protected with stainless steel guards
Advanced Digital Engine Management
ADEM A4 engine management system integrates speed control, air/fuel ratio control and ignition/detonation controls into a complete engine management system. control system with integrated digital ignition, engine protection and monitoring
Air System
- Separate circuit (water-to-air) aftercooler options available to match any application requirement. - Water-cooled exhaust manifold and turbo maintain ATEXcompliant skin temperature during operation
Improved Serviceability
- Front, right, and rear dipsticks - Remote oil and fuel filters - 12V and 24V electronic systems to improve application flexibility
Custom Packaging
Trust a Cat factory custom package to meet your exact petroleum application needs. Cat engines, generators, enclosures, controls, radiators, transmissions — anything your project requires — can be custom designed and matched to create a one-of-a kind solution. Custom packages are globally supported and are covered by a one-year warranty after startup.
Full Range of Attachments
Large variety of factory-installed engine attachments reduces packaging time
Testing
Every engine is full-load tested to ensure proper engine performance.
Product Support Offered Through Global Cat Dealer Network
More than 2,200 dealer outlets -Cat factory-trained dealer technicians service every aspect of your petroleum engine -Cat parts and labor warranty Preventive maintenance agreements available for repair-beforefailure options -S•O•SSM program matches your oil and coolant samples against Caterpillar set standards
Over 80 Years of Engine Manufacturing Experience
Ownership of these manufacturing processes enables Caterpillar to produce high quality, dependable products.
Over 80 Years of Engine Manufacturing Experience
Ownership of these manufacturing processes enables Caterpillar to produce high quality, dependable products.
Web Site
For all your petroleum power requirements, visit www.cat.com/oilandgas.
- Standard Equipment
- Optional Equipment
- Specs
- Docs
Standard Equipment
- Air Inlet System
- Turbocharger, separate circuit (SCAC)
- Single, right-side, center-mounted turbo with water-cooled turbine housing
- Air inlet, RH side, rear facing, 101.6 mm (4 in.) connection type
- Control System
- Electronic governing, PTO speed control
- Programmable ratings
- Cold mode start strategy
- Automatic altitude compensation
- Fuel cooled ECU
- Power compensation for fuel temperature
- Programmable low and high idle
- Electronic diagnostics and fault logging
- Programmable monitoring system (engine speed, temperature, pressure)
- J1939 broadcast (diagnostic and engine status)
- Certified electrical control system
- Derated engine: automatic ambient temperature compensation
- Cooling System
- Thermostats and housing, front-facing outlet — 51 mm (2.01 in) connection
- Jacket water pump — belt-driven, centrifugal
- Water pump — inlet RH front vertical inlet (pointing down) — 63 mm (2.48 in)
- Exhaust System
- Single, right-side, center-mounted turbo with water-cooled turbine housing
- Exhaust manifold — water-cooled
- Front turbo exhaust
- Flywheels and Flywheel Housing
- Mandatory selection of: SAE No. 1, SAE No. 2, or SAE No. 3 flywheel and housing SAE standard rotation
- Fuel System
- HEUI fuel system
- Fuel filter — secondary, LH front (2-micron high performance)
- Fuel transfer pump — left front
- Fuel priming pump — left front
- Lube System
- Crankcase breather — top rear
- Crankcase fumes disposal — RH
- Oil cooler — RH
- Oil filter — RH
- Oil pan — front sump, 31 L (33 qt) oil change capacity
- Oil filler — front top valve cover
- Oil level gauge — LH rear
- Engine oil pump — gear-driven
- Oil valve sampling, RH
- Power Take-Offs
- Crankshaft drive pulley — 2 grooves, 190 mm (7.5 in) diameter, 22.3 mm (0.88 in) wide
- General
- Vibration damper
- Lifting eyes
- Literature
- No paint
- Mandatory Options
- Flywheel housing and flywheel
- Primary filter/water separator
- Turbo orientation
Optional Equipment
- Air Inlet System
- Precleaner
- Air Inlet elbow
- Cooling System
- Water outlet elbow
- Coolant conditioner
- Emissions Certifications
- IMO certification
- Flywheels and Flywheel Housing
- Crankshaft seal
- Instrumentation
- Gauges and instrument panels
- Lube System
- Oil pans
- Drain and cover
- Remote oil filters
- Lubricating oils
- Mounting System
- Structural steel base
- Engine support -- front and rear
- Power Take-offs
- Crankshaft pulleys
- General
- Tool set
Specs
Overview
General Specifications
Emissions
Dimensions
Capacity for Liquids
SEE HOW C7 ACERT™ (Water-Cooled Manifold) COMPARES AGAINST FREQUENTLY COMPARED PRODUCTS.
- Brand
- Caterpillar
- Status
- Current
- Maximum Rating
- 275 BHP / 205 bkW
- Displacement
- 442 in³ / 7.2 l
- Minimum Rating
- 205 BHP / 153 bkW
- Governor and Protection
- Electronic (ADEM™ A4)
- Aspiration
- Turbocharged-Aftercooled
- Flywheel and Flywheel Housing
- SAE 1, 2, or 3
- Flywheel Teeth
- 156 (SAE 1), 134 (SAE 2), 126 (SAE 3)
- Rotation from Flywheel End
- Counterclockwise
- Stroke
- 5 in / 127 mm
- Bore
- 4.3 in / 110 mm
- Emissions
- EPA & CARB Non-Road Tier 3, EU Stage IIIA, EPA Marine Tier 2, IMO Tier II
- Length
- 41.5 in / 1053 mm
- Width
- 29.8 in / 758 mm
- Height
- 40.6 in / 1032 mm
- Weight
- 1386 lb / 629 kg
- Lube Oil System - Refill
- 4.8 gal (US) / 19 l
- Brand
- Caterpillar
- Status
- Current
- Maximum Rating
- 275 BHP / 205 bkW
- Displacement
- 442 in³ / 7.2 l
- Minimum Rating
- 205 BHP / 153 bkW
- Governor and Protection
- Electronic ADEM™ A4
- Aspiration
- Turbocharged-Aftercooled
- Flywheel and Flywheel Housing
- SAE 1,2, or 3
- Flywheel Teeth
- 156 (SAE 1), 134 (SAE 2), 126 (SAE 3)
- Rotation from Flywheel End
- Counterclockwise
- Stroke
- 5 in / 127 mm
- Bore
- 4.3 in / 110 mm
- Emissions
- EPA & CARB Non-Road Tier 3, EU Stage IIIA, EPA Marine Tier 2, IMO Tier II
- Length
- 41.5 in / 1053 mm
- Width
- 29.8 in / 758 mm
- Height
- 40.6 in / 1032 mm
- Weight
- 1386 lb / 629 kg
- Lube Oil System - Refill
- 36 gal (US) / 34 l
- Brand
- Caterpillar
- Status
- Current
- Maximum Rating
- 375 BHP / 280 bkW
- Displacement
- 538 in³ / 8.8 l
- Minimum Rating
- 205 BHP / 205 bkW
- Governor and Protection
- Electronic (ADEM™ A3)
- Aspiration
- Turbocharged-Aftercooled
- Flywheel and Flywheel Housing
- SAE 1 or 2
- Flywheel Teeth
- 113 (SAE 1), 134 (SAE 2)
- Rotation from Flywheel End
- Counterclockwise
- Stroke
- 5.8 in / 149 mm
- Bore
- 4.41 in / 112 mm
- Emissions
- EPA and CARB Non-Road Tier 3, EU Stage IIIA, IMO Tier II
- Length
- 43 in / 1092 mm
- Width
- 32.6 in / 828 mm
- Height
- 40.3 in / 1024 mm
- Weight
- 1578 lb / 716 kg
- Lube Oil System - Refill
- 8 gal (US) / 30.3 l